S_WipeBubbleWipes between two input clips with a bubble-warp process performed within the transition area. The Wipe Percent parameter should be animated to control the transition speed.In the Sapphire Transitions effects submenu.
Inputs:
|
|
Parameters:
-
Load Preset:
Push-button
.
Brings up the Preset Browser to browse all available presets for this effect.
-
Save Preset:
Push-button
.
Brings up the Preset Save dialog to save a preset for this effect.
-
Transition Dir:
Popup menu, Default: Wipe Off to Bg
.
Selects the direction of the transition.
-
Wipe Off to Bg:
transitions from the current layer to the Background.
- Wipe On from Bg: transitions from the Background to the current layer.
- Wipe On from Bg: transitions from the Background to the current layer.
-
Wipe Off to Bg:
transitions from the current layer to the Background.
-
Auto Trans:
Popup YES-NO, Default: No
.
If enabled, a transition is performed automatically between the first and last frames of the layer. If this is off, the transition is performed manually by animating the Wipe Percent parameter.
-
Wipe Percent:
Default:
0,
Range:
0 to 1.
Auto Trans must be disabled for this parameter to be used. It determines the transition ratio between the From and To inputs, and would normally be animated from 0 to 100 to perform a complete transition. The curve controlling this parameter can be adjusted for more detailed control over the timing of the wipe.
-
Edge Width:
Default:
1.4,
Range:
0.0138 or greater.
The width of the transition area. This can be adjusted using the Wipe Widget.
-
Angle:
Default:
0,
Range:
any.
The angle of the wipe direction in degrees from the right. This can be adjusted using the Wipe Widget.
-
Bubble Amount:
Default:
0.5,
Range:
0 or greater.
The magnitude of the bubble distortion.
-
Frequency:
Default:
8,
Range:
0.1 or greater.
The frequency of the bubble pattern. Increase to zoom out, decrease to zoom in.
-
Frequency Rel X:
Default:
1,
Range:
0.01 or greater.
The relative horizontal frequency of the bubble pattern. Increase for taller bubbles, decrease for wider bubbles.
-
Octaves:
Integer, Default:
8,
Range:
1 to 10.
The number of summed layers of noise. Each octave is twice the frequency and half the amplitude of the previous. A single octave gives a smooth texture. Adding octaves makes the result approach a fractal (1/f) noise texture.
-
Seed:
Default:
0.23,
Range:
0 or greater.
Used to initialize the random number generator. The actual seed value is not significant, but different seeds give different results and the same value should give a repeatable result.
-
Wrap:
X & Y, Popup menu, Default:
[
Reflect Reflect
].
Determines the method for accessing outside the borders of the source images.
-
No:
gives black beyond the borders.
- Tile: repeats a copy of the image.
- Reflect: repeats a mirrored copy. Edges are often less visible with this method.
- Tile: repeats a copy of the image.
-
No:
gives black beyond the borders.
-
Opacity:
Popup menu, Default: Normal
.
Determines the method used for dealing with opacity/transparency.
-
All Opaque:
Use this option to render slightly faster when
the input image is fully opaque with no transparency (alpha=1).
- Normal: Process opacity normally.
- As Premult: Process as if the image is already in premultiplied form (colors have been scaled by opacity). This option also renders slightly faster than Normal mode, but the results will also be in premultiplied form, which is sometimes less correct.
- Normal: Process opacity normally.
-
All Opaque:
Use this option to render slightly faster when
the input image is fully opaque with no transparency (alpha=1).
-
Crop Input Parameters:
Default:
0,
Range:
0 or greater.
These 4 parameters, Crop Top , Crop Bottom , Crop Left, and Crop Right , allow selecting a rectangular subsection of the input image to be processed. If the Wrap parameters are set to "No" the exposed borders will be transparent. If the Wrap is "Tile" or "Reflect" the source image is wrapped on the new cropped borders to fill the frame. This can make it easier to avoid artifacts due to distorting an image with bad edges.
-
Show Wipe:
Check-box, Default:
on.
Turns on or off the screen user interface widget for adjusting the Wipe Amt, Angle, and Edge Width parameters.This parameter only appears on AE and Premiere, where on-screen widgets are supported.